Cathy Shehorn (Customer) asked a question.
Cisco WLC 5508 Config Backup Script Help
Hello,
I am new to WhatsConfigured....and i am having issues trying to get my cisco WLCs backup scripts working...I think the biggest issue is that once you log in the "login as:" actually needs just a carriage return then you are prompted with a "User:" were you actually put in the username, then you get the "password:"....I am getting hung up on the "login as" as the @login or @connect will always see that as needing the username/password...
Any help would be greatly appreciated...
thanks
I believe this one will work. Let me know.
@Mike Rockwell (Progress Software) , thanks for the help on this....I tried running the above and i am stilling getting an error...
I have double checked that the credentials work and i can run the running configuration with the credentials i am using... however when i try to run the running configuration through WUG, i am unable to complete the task...
Thoughts?
connect "login as: "
READ
login as:
COMMAND END
connect "login as: "
Result: True
COMMAND START
write "\r\n"
WRITE
COMMAND END
write "\r\n"
Result: True
COMMAND START
read "User: "
READ
READ
(Cisco Controller)
User:
COMMAND END
read "User: "
Result: True
COMMAND START
write "userID"
WRITE
userID
COMMAND END
write "userID"
Result: True
COMMAND START
write "\r\n"
WRITE
COMMAND END
write "\r\n"
Result: True
COMMAND START
read "Password:"
READ
userID
Password:
COMMAND END
read "Password:"
Result: True
COMMAND START
write "password"
WRITE
6qxnrBBY
COMMAND END
write "password"
Result: True
COMMAND START
write "\r\n"
WRITE
COMMAND END
write "\r\n"
Result: True
COMMAND START
config paging disable
WRITE
config paging disable
READ
********
READ
(Cisco Controller) >config paging disable
(Cisco Controller) >
COMMAND END
config paging disable
Result: True
COMMAND START
show run-config
WRITE
show run-config
READ
show run-config
Press Enter to continue...
COMMAND END
show run-config
Result: False
Command failed without errors.
This is most likely caused by a failure to match the devices output with the expected output.
Do you need to verify that the output matches the appropriate prompt (Command, More, UserName, Password)?
When you run it manually you use the "show run-config"? Are there "more" prompts, and what are those prompts, in the CLI library for that OID, does it show the proper regex for that "more" command?
You might want to call Tech. Support and have them take a look.
When I run it manually, after entering the "show run-config" command and hit enter...I get the "Press Enter to Continue" i hit enter again and that is when i start seeing the config file...that is it really...not for sure why the script is not working 😢
@Mike Rockwell (Progress Software) , I know this has been a few months...but i have been working on this and i think this will work if i could get one more command in the script...
after the "show run-config" the WLC has a prompt that says "Press Enter to continue.."
I have tried several commands, but nothing I try works...how would you get around this?
thanks in advance
You could try putting a '@Read "Press Enter to Continue"' followed on the next line "@write $(CommandTerminator)"
The CommandTerminator will send an enter.
Hi Everyone
The following task script has been tested successfully on a Cisco WLC 2500 series and a 3500 series
@connect "login as: "
@write $(LoginTerminator)
@read "User: "
@write "$(Settings.UserName)"
@write $(LoginTerminator)
@read "Password:"
@write "$(Settings.Password)"
@write $(LoginTerminator)
#- @enable
# for cisco WLC
[-] config paging disable
[running-confg, trim-before=/(V|v)ersion/, remove-lines="ntp clock-period"] show run-config { "Press Enter to continue...", $(CommandTerminator) }
@logout